SMR has the following Calibration positions available.
POSITION TITLE: Sr. PMEL Technician (Electronics)
LOCATION: Tinker AFB, Oklahoma City, OK
HOURS: 6:45 am-3:30 pm, Monday-Friday (some overtime may be required)
Positions Available: 2
BASIC REQUIREMENTS:
1. Minimum four (4) years experience in Test, Maintenance, and Diagnostic Equipment (TMDE) calibration and repair, preferably in a military calibration lab. Experience to include inspecting, troubleshooting, repairing, overhauling, aligning, calibrating, and certifying TMDE, metrology laboratory working standards and safe work practices/procedures.
2. Completion of the Military metrology training program or similar training.
3. Good working knowledge of calibration and maintenance of K1, K8, K5, K3, K4 TMDE; consisting of the following: PRT/SPRT, Thermocouples, Power Supplies, High Voltage, Microwave devices, Generators, Spectrum Analyzers, Power Sensors, Fiber Optics, Sound pressure level, Light Intensity and general purpose TMDE.
4. Possesses the knowledge required to read and analyze block, schematic, wiring and logic diagrams.
5. Ability to troubleshoot and repair non-functioning TMDE.
___________________________________________________________________________________________________
POSITION TITLE: Sr. PMEL Technician (Phy/D)
LOCATION: Tinker AFB, Oklahoma City, OK
HOURS: 6:45 am-3:30 pm, Monday-Friday (some overtime may be required)
Positions Available: 2
BASIC REQUIREMENTS:
6. Minimum four (4) years experience in Test, Maintenance, and Diagnostic Equipment (TMDE) calibration and repair, preferably in a military calibration lab. Experience to include inspecting, troubleshooting, repairing, overhauling, aligning, calibrating, and certifying TMDE, metrology laboratory working standards and safe work practices/procedures.
7. Completion of the Military metrology training program or similar training.
8. Good working knowledge of calibration and maintenance of K6 TMDE; consisting of the following: Pressure, Force, Mass, Optics, Linear Measurements, Air Flow, and Temperature. Including use and calibration of Gage Blocks, calipers, micrometers, ring gages, plug gages, thread gages.
9. Possesses the knowledge required to read and analyze block, schematic, wiring and logic diagrams, and blue prints.
10. Ability to troubleshoot and repair non-functioning TMDE.
PHYSICAL REQUIREMENTS
ACTIVITY OFTEN
CLIMBING X
STOOPING X
KNEELING X
REACHING X
STANDING X
SITTING X
WALKING X
PUSHING X
PULLING X
TALKING X
HEARING X
Lifting/Moving Requirements – up to 50 pounds
Please send resume to Mark Murray at mark. murray. ctr@inker. af. mil.
Pardon my ignorance but K5 is usually paired up with K6. :?
Physical/Dimensional. Temperature being considered to go along with it.
I doubt many people with 4 years experience are going to have the experience you list for electronics with Platinum Resistance Thermometers and all the other equipment.
I suggest moving the K5 to the other technician slots.
The only temperature related things I would think your average K1/K8 tech would be touching is thermocouple related meters being tested on the 5520A or other equipment.
2nd - Tinker being a IIA and a depot type lab is probably fairly large and I would think the K1/K8 and K3/K4 would probably be seperated too.
Question, is Tinker working on DOL wage determination or have they gone union? Bsically what is the salary?
Tinker is under a CBA (union). The wages for the Sr. PMEL Technician is $26. 20 with a 4% increase in Oct. 09. The health and welfare is $237. 00 per pay period (every 2 weeks). The company also pays for the long and short term disability, life insurance (1 X salary). There is vacation and sick/personal time (40 hours). Medical, dental, and vision is available.
is there only two tech levels? when i was at Hill, there were 3. P.S. to all, i loved working at a type 2A.
There are three levels, PMEL Tech, Sr. PMEL Tech, and Lead Tech. We are looking for Sr. PMEL Tech (Tech II). This is a good area to work with variety of equipment to work on. We are looking for 4 people because the Civil Service on base just hired and lost technicians to them.
Hey Donnie, how are things? Thought I'd say hello, and thanks.
Terry Brown
Wow!! the Gov't stealing your techs!!!?
How are u Donnie?
Leo