Welcome, Guest. Please login or register.
07-29-2021 -- 17:32:20

Login with username, password and session length

Top 10 Posters

flew-da-coup (1303)
Hawaii596 (1023)
griff61 (580)
Hoopty (548)
docbyers (544)
MIRCS (535)
CalLabSolutions (523)
Thraxas (498)
  • Total Posts: 19331
  • Total Topics: 3692
  • Online Today: 117
  • Online Ever: 242
  • (04-19-2014 -- 19:20:34)
Users Online
Users: 0
Guests: 29
Total: 29

Author Topic: Sr. PHYS/D Metrology Technician at New Orleans  (Read 865 times)

Offline Donaldr1955

  • 3-level
  • **
  • Posts: 33
  • Action Taken: +0/-0
Sr. PHYS/D Metrology Technician at New Orleans
« on: 05-29-2020 -- 16:30:37 »
SMR is currently hiring a Metrology Technician at our Belle Chasse JRB, LA location. Must be able to work independently. Successful candidate determines and performs operations required to calibrate and certify electronic, physical/dimensional, and test equipment. He/she will utilize Navy calibration methods and techniques based on principles of measurement science, technical analysis of measurement problems, and accuracy and precision requirements. Metrology Technician will inspect measuring and test equipment for preventive maintenance, cleanliness, and safety requirements, analyze and interpret results of measurements and calibrations using mathematical formulas, and document result of measurements and calibrations on calibration certificates and calibration correction charts. Qualified candidates must have a well-rounded skill set in Physical Mechanical areas.

Job Requirements:
•   Minimum six (6) years’ experience in Physical Mechanical areas working on Test, Maintenance, and Diagnostic Equipment (TMDE) calibration and repair, preferably in a military calibration laboratory. Experience with pressure calibration, O2 calibration, proving rings and force calibration, vibration, flow and/or temperature is preferred.
•   Experience to include: Physical Mechanical areas, inspecting, troubleshooting, repairing, overhauling, aligning, calibrating, and certifying TMDE, metrology laboratory working standards and safe work practices/procedures.
•   Completion of a DOD accredited Navy/Marine/PMEL Calibration School or an Associate Degree in Metrology.
•   Completion of the Advanced Physical/Dimensional course is a plus
•   Possesses the knowledge required to read/analyze block, schematic, wiring and logic diagrams.
•   Ability to troubleshoot and repair non-functioning TMDE
•   Must have or be able to hold a secret clearance

Required experience:
•   Metrology: 8 years
•   Physical Mechanical: 6 years

Candidates must be physically capable of lifting and moving 50 lbs.
Candidates must be available for up to 25% on-site work.

Contractors can live in base housing if there is space available. Children can also attend the base school if there is space available.

Please send resume to lrobertson@smrpcola.com.

Science and Management Resources, Inc. (SMR) is an Equal Opportunity Employer. SMR will not discriminate against any employee or applicant based on gender, race, national origin, religion, sexual orientation, veteran status, age, or any other classification protected by federal, state, or local law. SMR and all subcontractors are committed and required to take Affirmative Action to employ and advance qualified women, minorities, disabled individuals, and eligible veterans as consistent with federal law.
« Last Edit: 06-01-2020 -- 19:26:22 by Donaldr1955 »

Offline Donaldr1955

  • 3-level
  • **
  • Posts: 33
  • Action Taken: +0/-0
Re: Sr. PHYS/D Metrology Technician at New Orleans
« Reply #1 on: 06-15-2020 -- 20:37:39 »
This position is filled.


DISCLAIMER:  This site is not an official US Air Force site, it is intended for private use only.  It is not endorsed, in any way, by the US Air Force, the DoD, or any other governmental agency.  Additionally, all information found within this site is just that, it is NOT meant to be used in place of authorized publications.

All logos and trademarks in this site are property of their respective owner.

All forum content is the property of the respective poster, all the rest © 2004-2017 by PMEL Forum.