Welcome, Guest. Please login or register.
Did you miss your activation email?
06-25-2019 -- 08:11:04

Login with username, password and session length

Top 10 Posters

flew-da-coup (1302)
Hawaii596 (1010)
griff61 (573)
Hoopty (548)
docbyers (544)
MIRCS (535)
CalLabSolutions (511)
Thraxas (498)
  • Total Posts: 19087
  • Total Topics: 3565
  • Online Today: 67
  • Online Ever: 242
  • (04-19-2014 -- 19:20:34)
Users Online
Users: 0
Guests: 58
Total: 58

Author Topic: Equipment selection  (Read 409 times)

Offline OlDave

  • 5-level
  • ***
  • Posts: 331
  • Action Taken: +21/-0
Equipment selection
« on: 04-08-2019 -- 11:58:12 »
Has anyone had much experience with Additel products? Specifically, the Additel 760 Automatic Handheld Pressure Calibrator.

I have always wanted to try their instruments but have never had a chance to evaluate any of them. If anyone has either positive or negative experience with them I would appreciate any info you would be willing to share.

PM me if you don't want to post publicly.

Offline OldSchl

  • Pinger
  • *
  • Posts: 11
  • Action Taken: +0/-0
    • Email
Re: Equipment selection
« Reply #1 on: 04-08-2019 -- 12:51:06 »
I've used the 761 for years and I would highly recommend them. The customer service is very responsive and the instruments have been very reliable.
Virtue is more to man than either water or fire.   I have seen men die from treading on water and fire, but I have never seen a man die from treading the course of virtue.   - Confucius

Offline CalLabSolutions

  • Global Moderator
  • 7-level
  • *****
  • Posts: 511
  • Action Taken: +5/-2
    • Cal Lab Solutions
    • Email
Re: Equipment selection
« Reply #2 on: 04-08-2019 -- 16:11:40 »
I have one also... 
We are adding Pressure Calibration to Metrology.NET and found it to be a great tool for not only automation but also Training.  It's small lightweight, battery operated and portable!

What I like the most is how well it ramps up or down to the set point and hits it without overshoot.

Michael L. Schwartz
Automation Engineer
Cal Lab Solutions
  Web -  http://www.CalLabSolutions.com
Phone - 303.317.6670

Offline NC-Cals

  • 3-level
  • **
  • Posts: 46
  • Action Taken: +0/-0
    • Email
Re: Equipment selection
« Reply #3 on: 04-22-2019 -- 13:00:03 »
I have calibrated several of the low pressure standards. The 0 to 1 in-H2O and 0 to 10 in-H2O model has the best regulation I've seen.  When I calibrate them, I use the Additel to regulate the pressure and it holds steady our to 5 digits 2 on our 7250LP. They are also easy to adjust when needed. Additel has been very responsive for technical assistance. Their handheld process calibrators are also good quality.


DISCLAIMER:  This site is not an official US Air Force site, it is intended for private use only.  It is not endorsed, in any way, by the US Air Force, the DoD, or any other governmental agency.  Additionally, all information found within this site is just that, it is NOT meant to be used in place of authorized publications.

All logos and trademarks in this site are property of their respective owner.

All forum content is the property of the respective poster, all the rest 2004-2017 by PMEL Forum.