Welcome, Guest. Please login or register.
01-19-2021 -- 08:05:30

Login with username, password and session length

Top 10 Posters

flew-da-coup (1303)
Hawaii596 (1015)
USMCPMEL (857)
griff61 (580)
Hoopty (548)
docbyers (544)
MIRCS (535)
CalLabSolutions (523)
PMEL_DEVIL-DOG (509)
Thraxas (498)
Members
Stats
  • Total Posts: 19268
  • Total Topics: 3662
  • Online Today: 82
  • Online Ever: 242
  • (04-19-2014 -- 19:20:34)
Users Online
Users: 0
Guests: 22
Total: 22


Author Topic: Lockheed Martin Metrologist Position Filled  (Read 4275 times)

Offline Wisdo

  • Pinger
  • *
  • Posts: 19
  • Action Taken: +0/-1
Lockheed Martin Metrologist Position Filled
« on: 05-16-2011 -- 13:42:42 »
Lockheed Martin MS2 has a rare permanent opening for a Metrologist to provide engineering support to Metrology Technicians and Metrologists in the areas of technical assistance and automated calibration software development to improve laboratory production and efficiency in the calibration and repair of inspection, measuring and test equipment.  You will participate in/conduct equipment capital planning activities, internal laboratory and vendor evaluations, and system/personal computer maintenance.  Assist/develop Metrology measurement methods, procedures, and measurement uncertainty calculations.  Assistance with and maintenance of ISO/IEC 17025 accreditation.

Please note that this position will require Extended Duty (EDY) Assignment to the Minneapolis St.  Paul area (Eagan, MN) facility until the end of 2012.  The permanent work location for this position is Owego, NY beginning in December of 2012
This position requires a BS Degree in related discipline, such as Engineering, Physics or other Sciences, or equivalent experience.  Experience in the calibration and repair of a broad range of inspection, measuring and test equipment.  Experience in determining calibration requirements, performing uncertainty calculations, and developing manual and automated calibration procedures.  Experience in the use of computers, connectivity, Microsoft Office, instrumentation control utilizing automated calibration software.  Familiarity with ANSI Z540 or ISO/IEC 17025 standards.

In order to be considered, please visit our website (www. lockheedmartinjobs. com) and search for position number 199673BR, or send a copy of your resume and salary requirements to leo. e. oberto@lmco. com
« Last Edit: 09-19-2011 -- 21:08:21 by Wisdo »

Offline michthai

  • 3-level
  • **
  • Posts: 47
  • Action Taken: +0/-0
Re: Lockheed Martin Metrologist Opening
« Reply #1 on: 05-17-2011 -- 11:42:42 »
Not too sure how "permanent" this position is considering that you are being hired as a contractor by CTL Resources.

Offline Wisdo

  • Pinger
  • *
  • Posts: 19
  • Action Taken: +0/-1
Re: Lockheed Martin Metrologist Opening
« Reply #2 on: 09-19-2011 -- 21:07:14 »
Dear michthai, please do not post false information in anyone's thread. This position has been filled and was a position with Lockheed Martin...NOT A CONTRACTOR.
I don't know where you got your information from but next time PM me with any questions and I will answer them to the best of my ability.
Hopefully your false comment did not deter anyone from applying.

 

DISCLAIMER:  This site is not an official US Air Force site, it is intended for private use only.  It is not endorsed, in any way, by the US Air Force, the DoD, or any other governmental agency.  Additionally, all information found within this site is just that, it is NOT meant to be used in place of authorized publications.


All logos and trademarks in this site are property of their respective owner.

All forum content is the property of the respective poster, all the rest 2004-2017 by PMEL Forum.